#INSTALLATION PBP3 MPLAB X INSTALL#
#INSTALLATION PBP3 MPLAB X MANUAL#
#INSTALLATION PBP3 MPLAB X REGISTRATION#
#INSTALLATION PBP3 MPLAB X PRO#
#INSTALLATION PBP3 MPLAB X SOFTWARE#

main: The digital I/O pins on the CHIPINO are D0 through D13. We will use this marker in a future GOTO command. The main program loop begins with the label main followed by a semi-colon.

The contents of chipino.bas are shown in Appendix C. The main point is you can modify the chipino.bas file if you are an experienced programmer. You don t have to worry about any of this if you are new to programming Microchip PICs. The configuration settings are also handled by the chipino.bas file so the MCLR pin is external and the write protection is turned off. Therefore you can modify it for anything you want to be included in every CHIPINO project you create.ДЎ1 include 'chipino.bas' The chipino.bas file also sets the program speed to match the 16 MHZ oscillator on the CHIPINO module. PBP3 places the contents of the chipino.bas file directly at that location just as if you typed it in. You can view this file to see the setup and can modify it if you want. This file defines all the digital pins (D0 thru D13) and analog pins (A0-A4). The first section is required to include the chipino.bas file.

#INSTALLATION PBP3 MPLAB X SOFTWARE#

Connection Table CHIPINO - Pin Digital 13 to a-11 CHIPINO - GND to a-10 Jumper - e-10 to f-10 1k ohm - e-9 to f-10 Red LED - Anode i-11, Cathode i-10ДЎ0 Figure 2-2: Flash LED Schematic Software '**************************************************** '* Name : flash.pbp '* Author : Chuck Hellebuyck '* Notice : Copyright (c) 2012 Electronic Products '* : All Rights Reserved '* Date : '* Version : 1.0 '* Notes : '* : CHIPINO - Pin Digital 13 to a-11 '* : CHIPINO - GND to a-10 '* : Jumper - e-10 to f-10 '* : 1k ohm - e-9 to f-10 '* : Red LED - Anode i-11, Cathode i-10 '**************************************************** include 'chipino.bas' main: HIGH D13 PAUSE 500 LOW D13 PAUSE 500 GOTO main 'LED on 'Delay 1/2 second 'LED off 'Delay 1/2 second 'Loop back and do it again The software is quite simple because it uses some of the commands that make PBP3 easier to use that many other compilers. Figure 2-2 also shows the schematic for this project. The connections can be reproduced based on the table of connections below. Figure 2-1: Flash LED Project Hardware The hardware is built on a breadboard that has letters lined up with the column of connections and numbers for the rows. The CHIPINO powers the breadboard and the red LED will flash at a rate of ВЅ second on and ВЅ second off. Figure 2-1 shows the completed project built into a breadboard. This is a simple project but proves out the whole process of writing software, programming the microcontroller and watching the application run. We re now ready to program the BASIC CHIPINO.Д© Flash an LED Now we can write our first program that will simply flash an LED connected to the pin 13 of the CHIPINO module. Follow through all the installation screens until the PICkit 2 is completely installed and a PICkit 2 icon appears on your desktop.

#INSTALLATION PBP3 MPLAB X INSTALL#

The compiler will step you through several screens shown in Figures 1 thru.Д§ Figure 11: Installation in Progress Screen Figure 12: Final MicroCode Studio Screen After installation is complete, start Microcode studio and it should look similar to the picture in Figure 13.ДЁ Figure 13: MicroCode Studio IDE Install the PICKit 2 Programmer Install the PICkit 2 Standalone Software from the PICkit 2 CD by clicking on the PICkit2Setup installation file. 4) Setup the PICkit 2 software included on the PICkit 2 CD Installing MicroCode Studio and PBP 3 You need to run the PBP 3 installation file so run the PBP3_Setup file to install the PBP 3 compiler.

#INSTALLATION PBP3 MPLAB X PRO#

3) Install MicroCode Studio Software (this is part of the PICBASIC PRO installation). This will enable the Student version of PBP3.

#INSTALLATION PBP3 MPLAB X REGISTRATION#

2) Install the PBP3 compiler and when asked for a registration key enter the registration key included on your sales receipt. The steps we will take are: 1) Download the PBP3 Demo version from at: or load from the CD included. We have to set all this up on your PC before we can create the first project. The PICkit 2 programmer software has a stand-alone application which allows us to use the PICkit 2 or with the MicroCode Studio editor to one click compile and program the PIC microcontroller using the ICSP. The editor is called the MicroCode Studio.

#INSTALLATION PBP3 MPLAB X MANUAL#

1 BASIC CHIPINO Manual Installing the Software The PICBASIC PRO compiler sample version comes with its own windows editor for writing the programs and sending the binary file to the programmer.

Installation pbp3 mplab x